Robbins Hangar

Schweiss Doors

Whenever he has down time, pilot Larry Robbins can be found hanging out at home in LaFollette, TN where he has access to his airplanes in an air park subdivision that features its own landing strip. His hangar is fitted with a bifold liftstrap door from Schweiss Doors. It measures 44' x 14-1/2' and is equipped with auto latches and a remote opener.

“The straps just made so much sense to me,” Robbins says. "I was the first one on this field to have a Schweiss door. When I built my hangar, I also built another one for a friend who also has a Schweiss door. A few years later I built a hangar for another friend and it has a Schweiss door on it. Now there are others here that have Schweiss doors on them. I looked at one other manufacturer’s door that had a design that would go up higher, but it didn’t do anything for me. My door has been working well for me, it’s quiet and goes up and down when I ask it to.”

When Robbins isn’t helping neighbors in his unofficial role as a Schweiss representative, he works as an independent systems engineer. He spent 10 years, most of it on the road, supporting the development of the Boeing 787 Dreamliner. Now, his time off gets him back to his Deerfield Resort subdivision, nestled between the Cumberland Mountains and the foothills of the Great Smoky Mountains on the peninsula of Norris Lake, north of Knoxville, TN.

Parked within the hangar are his 1946 J3 Piper Cub and Glasair 1 experimental that he built himself. Robbins' “Pilot Cave” is something to behold. The 3,600 square feet floor is tiled and has a full-scale inlaid replica of a P-51 Mustang, complete with machine guns, taking center stage. He said he wouldn’t have tiled the floor but did it because of what he called "the world’s worst concrete job". Also in his hangar is a 1969 Plymouth Barracuda Fastback with 28,000 miles on it. A similar Barracuda was his first car.

In 1980, the kitplane industry was revolutionized by the introduction of the Glasair, the world’s first pre-molded composite kitplane. The Glasair is an ultimate high-performance aircraft. With its Lycoming engine, the Glasair is a fast, sleek, aerobatic machine that will take passengers across the country at a maximum speed of 260 mph in mere hours. Glasair kits have been delivered worldwide.

“I built it in my basement,” Robbins says. “I quit keeping track of time when I saw how long it was going to take. It was a 10-year project from start to finish. We used to live in Rockford, IL and relocated to the Atlanta area. The plane was maybe about half done. I loaded it on a trailer behind my car. At every gas station I stopped at they wanted to know if anyone was hurt. The time that you are building something like that you’re dreaming about the day you will have it done and be able to take off and go where you want to go. I sat in the airplane and thought, ‘My Lord, what have I done.’ It doesn’t have the potential to hurt anyone until you rev up the engine and pull back on the stick — it went fine. It was kind of like your first solo; you’ll never, ever forget it.”

But it’s the J3 Piper that commands the most interest.

“My dad bought it in 1955 for $175 — the whole thing, including the engine. It had been sitting on floats on the Illinois River when a storm came through and blew one wing down into the river. It was fetched out of the river and taken apart. Dad bought it as a basket case. Later on when dad told me where he got it and how much he spent, I told him he should have bought the floats; they were a set of EDO 1320s, which would be worth as much as the airplane today. Dad said he didn’t have $175 for the airplane and they wanted $500 for the floats,” recalled Robbins.

His dad spent a couple of years trying to reassemble it. When he ran out of time and money he hung it up in the rafters of his farm machine shed. It hung there for years and years until Larry was nearing graduation from high school. Over the three years he was attending aviation school they cleaned it up together and it’s been flying since 1975.

“Dad was one of those proverbial student pilots who never got his pilot’s license,” Robbins says. “Every now and then he’d pull the Cub out, we had a strip on our farm, and fly it around. I said, ‘Dad, you really ought to get your license.’ He responded by saying he was just flying it over his own property.”

About Schweiss Doors

Schweiss-logoSchweiss Doors is the premier manufacturer of hydraulic and bifold liftstrap doors. Doors are custom made to any size for any type of new or existing building for architects and builders determined to do amazing things with their buildings, including the doors. Schweiss also offers a cable to liftstrap conversion package. To learn more, visit or

And to learn about Schweiss' new Build Your Own Door Kit, which gives customers the plans and essential components to build their own Schweiss Doors, visit

facebook40    twitter40    pinterest40    instagram40    linkedin40    youtube40

^ Back To Top